Register
It is currently Thu Jan 18, 2018 10:59 pm View active topics

All times are UTC - 5 hours


Search found 4332 matches
Search these results:

Author Message

 Forum: 2.7 Liter   Topic: 2.7 mods to stop sludging

Posted: Tue Jan 09, 2018 1:58 pm 

Replies: 12
Views: 202


When oil circulation is halted ..........the oil gets cooked........and sludge fills the passages.

When oil circulation is halted the least of your worries is going to be sludge.

 Forum: Electrical and HVAC   Topic: 3.5 V6 - check engine light after a boost or battery charge

Posted: Tue Jan 02, 2018 4:09 pm 

Replies: 5
Views: 137


Check and see what code it there.

 Forum: General Maintenance   Topic: Not Starting

 Post subject: Re: Not Starting
Posted: Tue Dec 26, 2017 11:16 pm 

Replies: 12
Views: 307


If the clutch must be pushed in to start you might have a bad switch. Turn the headlights on went starting and see if they dim. If not it's not the battery. The reason it might have started the first time could have been closing the hood shook the carbon loose in the starter. But most times you only...

 Forum: Electrical and HVAC   Topic: Odd heat issue

 Post subject: Re: Odd heat issue
Posted: Thu Dec 21, 2017 5:04 pm 

Replies: 8
Views: 283


taman76 wrote:
Interesting I am not the only one seeing this issue right now.Terry, that is probably what is wrong. Like I said, I put a new cap on and still having the same issue now and again.



Tis the season.

The motor should be located next to the gas pedal.

 Forum: Electrical and HVAC   Topic: Odd heat issue

 Post subject: Re: Odd heat issue
Posted: Wed Dec 20, 2017 9:23 pm 

Replies: 8
Views: 283


Blend door motor. Also can be a rad cap going bad. Mostly the b/door motor.

 Forum: Electrical and HVAC   Topic: Heater Core/Heated Seats/RearDefroster

Posted: Sun Dec 03, 2017 10:53 am 

Replies: 18
Views: 570


We used HOAT in our postal vehicles and it was green. Came in bulk 55 gal drums. Just make sure you read the container your coolant comes in. I'm starting to think this is a money maker for the manufactures. You can only use their fluid in their products. Convenient.

 Forum: Electrical and HVAC   Topic: Blown fuse

 Post subject: Re: Blown fuse
Posted: Sun Dec 03, 2017 10:46 am 

Replies: 3
Views: 183


I had something similar on my concorde. Turned out to be the rad fan. The bearing was going and would sometimes blow the fuse. Got a J/Y fan assembly for $40 problem solved. Dealer wanted $275 just for the motor.

 Forum: Electrical and HVAC   Topic: Heater Core/Heated Seats/RearDefroster

Posted: Sun Dec 03, 2017 10:39 am 

Replies: 18
Views: 570


Pressure test the system. Seems to me it's not holding any pressure with the symptoms you are getting. Without the pressure the pump will not push the coolant thru the heater core.

 Forum: Electrical and HVAC   Topic: Heater Core/Heated Seats/RearDefroster

Posted: Fri Dec 01, 2017 1:05 am 

Replies: 18
Views: 570


The problem with using air to blow it out is that air can compress and get thru small holes , so most of the core could still be plugged and not allow water/coolant (hard to compress) to go thru. Best to reverse flow it with water. -Andrew Yes with just using air. The best way to flush is with air ...

 Forum: General Maintenance   Topic: Long term storage

 Post subject: Re: Long term storage
Posted: Fri Dec 01, 2017 12:39 am 

Replies: 8
Views: 376


What I always did was change oil and check all the fluids. Then right before putting it away let it set over night then drive it for a few minutes maybe around the block, don't let it get to operating temp. Just to blow out any water in the exhaust and put it away and don't touch it till you are goi...

 Forum: 2.7 Liter   Topic: Water leaking from somewhere

Posted: Tue Nov 28, 2017 7:32 pm 

Replies: 9
Views: 380


If I was doing the job (which I did on my own car) I would upgrade everything with OEM parts. If you are going to use everything over and just replace the water pump then the second pump is what you would use. If any of your guides need replaced Chrysler does not make the old style any more so you w...

 Forum: 2.7 Liter   Topic: Clicking sound when starting cold

Posted: Tue Nov 28, 2017 7:20 pm 

Replies: 11
Views: 586


It's not a upgraded o-ring it's a upgraded tensioner. It will come with a new o-ring. The dealers will only have the upgraded one. Just be sure the new tensioner has a clip on the bottom.

 Forum: Electrical and HVAC   Topic: Heater Core/Heated Seats/RearDefroster

Posted: Fri Nov 24, 2017 10:28 am 

Replies: 18
Views: 570


I'll bet you are low on coolant that is why your heater isn't working. The relay/thermister under your seat is most likely why your seat heater is not working. I replaced two on mine. It looks just like a big relay but costs about $60. Best to fine one in the junkyard. They charge about $5 I keep a ...

 Forum: 2.7 Liter   Topic: Coolant Outlet Housing replacement

Posted: Sat Nov 18, 2017 5:31 pm 

Replies: 12
Views: 429


A very easy job that I would do for 50 bucks Canadian so less than that in USD..... :mrgreen: Simply DISCONNECT THE THROTTLE CABLE and remove the upper intake manifold However slowly one bolt at a time in the correct sequence and only two turns per bolt until all are loose before taking all the way...

 Forum: 2.7 Liter   Topic: Coolant Outlet Housing replacement

Posted: Wed Nov 15, 2017 9:50 am 

Replies: 12
Views: 429


It seems like a very expensive repair for such a simple thing. I would only use a factory part and get a mechanic to do it on the side or do it yourself if you think you can. A lot of dealership mechanics work from home you just need to ask them. I know I did for the 40 years I was one and this was ...
Sort by:  
Page 1 of 289 [ Search found 4332 matches ]


All times are UTC - 5 hours


Jump to:  


Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Style originally created by Volize © 2003 • Redesigned SkyLine by MartectX © 2008 - 2010